GETTING FAMILIAR WITH PLUMBING: YOUR STARTING POINT FOR WHEN INSTALLING A BATHTUB

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Blog Article

Click Here

What are your thoughts on Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Setting up a tub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and also often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably challenging job. If the old tub is easily available, the job can relocate immediately; if you need to open up a wall surface to remove the old bathtub and position the new bath tub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually certified on your own for the work and also fit trying it. As opposed to working with a professional to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This short article will certainly help you install a brand-new tub in your washroom if you have actually currently bought a brand-new tub and also don't require to change the setup of your previous water system pipes.
Your tools and material checklist must consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Setup


    To start with, the sustaining framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
    Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
    Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last setting.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be fairly problematic due to the restricted accessibility that is often the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
    Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.

    Setting up the Tub


    Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little points.
    The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level checks out level.
    To mount faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
    Turn on the supply of water and also inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the tub as well as likewise examine the overflow outlet and also the normal outlet for leaks.
    Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait till the bath tub has been used at least once as this will certainly settle it right into its last position.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
    If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and the sink. Safeguard the tap in position with the producer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind needs to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Bathtub


    In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a rigid seal, causing the water to permeate the wall surface between the bath and the tiling, resulting in problems with dampness and also feasible leaks to the ceiling below.
    You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and also cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can split relatively early if you do not take into consideration this movement prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently readily available on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    We are very intrigued by How to Install a Bathtub and I am hoping you liked the post. Enjoyed reading our posting? Please share it. Help others check it out. Thank you for going through it.


    24/7 plumbers for emergencies.

    Report this page